0. INTRODUCTION
This specification provides the definition of the Equipment
damage and repair estimate message (DESTIM) to be used in
Electronic Data Interchange (EDI) between trading partners
involved in administration, commerce and transport.
1. SCOPE
1.1 Functional Definition
A message for use by the container repair, shipping and leasing
industry. It may be used by a container equipment repair depot
to send an owner or user a description of damages to the
equipment, as an estimate of the repair actions and costs
needed to rectify such damages. A recipient owner may forward
the estimate to a lessee. The message may also be used by an
owner or lessee as an authorization message to the repair depot
to perform the repairs indicated in the estimate, and as an
acknowledgment of his willingness to pay for those repairs
indicated in the estimate for his account.
1.2 Field of Application
The Equipment damage and repair estimate message may be used
for both national and international trade. It is based on
universal commercial practice and is not dependent on the type
of business or industry.
1.3 Principles
It is envisaged that the Equipment Damage and Repair Estimate
Message may be used as follows:
1. By an equipment depot to the owner or lessee of damaged
equipment after the equipment has been returned by a lessee, in
order to indicate needed repairs and to request authorization
to perform repair work.
2. By an equipment owner to a lessee to provide repair cost
estimates, and to request the lessee's acknowledgment of
willingness to pay costs allocated to lessee's account.
3. By an equipment owner or lessee to a repair depot to give
authorization to have the damaged equipment repaired.
2. REFERENCES
See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction,
Section 1.
3. TERMS AND DEFINITIONS
See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction,
Section 2.
4. MESSAGE DEFINITION
4.1 Data Segment Clarification
This section should be read in conjunction with the Branching
Diagram and the Segment Table which indicate mandatory,
conditional and repeating requirements.
4.1.1 Header section
Information to be provided in the Header section:
0010 UNH, Message header
A service segment starting and uniquely identifying a message.
The message type code for the Equipment damage and repair
estimate message is DESTIM.
Note: Equipment damage and repair estimate messages conforming
to this document must contain the following data in segment
UNH, composite S009:
Data element 0065 DESTIM
0052 D
0054 96B
0051 UN
0020 BGM, Beginning of message
A segment to indicate the beginning of a message and to
transmit identifying number and type of message.
0030 DTM, Date/time/period
A segment to indicate date and time of the event being reported
or requested by the message.
0040 GIS, General indicator
A segment to indicate whether the container is damaged and not
available for leasing or still available for leasing (i.e.
without damages that require repair).
0050 CUX, Currencies
A segment to specify various currencies associated with the
message such as labor currency, material currency and Damage
Protection Plan currency.
0060 RFF, Reference
A segment indicating a reference number applicable to the
entire estimate, such as customer reference, lease number, etc.
0070 FTX, Free text
A segment to specify free form or processable supplementary
information (such as coverage of equipment under an Approved
Continuous Examination Program [ACEP] complying with the
International Convention for Safe Containers [CSC]) that
applies to the entire message.
0080 Segment group 1: EQD-DIM-IMD
A group of segments to identify equipment-related data,
including equipment number, type, size, etc.
0090 EQD, Equipment details
A segment to specify equipment-related data, including
equipment number, type, size, etc.
0100 DIM, Dimensions
A segment indicating the actual dimensions of the equipment,
if the size and type is not known.
0110 IMD, Item description
A segment to specify material of which the equipment is and
other specialized data (such as maximum gross weight, tare
weight, etc.).
0120 Segment group 2: NAD-MOA-SG3
A group of segments to identify parties, such as owners,
lessors, users, lessees, equipment depots, agents, etc.,
sending or receiving the estimate. The group also summarizes
responsibility for repair costs by party, with a detailed
enumeration and allocation of such costs, including labor, tax
on labor, materials, tax on materials, subtotal labor and
materials, subtotal tax, and grand totals for the estimate.
0130 NAD, Name and address
A segment to identify the name, address, and function of
parties to whom the estimate is sent.
0140 MOA, Monetary amount
A segment used to indicate labor, materials, and tax cost
attributable to a party pertaining to the entire estimate.
0150 Segment group 3: CTA-COM
A group of segments to identify individuals or departments
to whose attention the estimate will be directed.
0160 CTA, Contact information
A segment to identify a person or department to whom
communications should be directed.
0170 COM, Communication contact
A segment to identify telephone, fax, etc. numbers at
which the person or department to receive the estimate
may be contacted.
0180 Segment group 4: TDT-LOC-DTM
A group of segments identifying details of the transport, if
any, such as carrier, mode and means of transport, locations
and related date(s) and time(s).
0190 TDT, Details of transport
A segment to specify details of transport such as carrier,
the means of transport, voyage number etc.
0200 LOC, Place/location identification
A segment to specify any locations related to the transport
details such as ports, terminals, etc.
0210 DTM, Date/time/period
A segment to specify associated date(s) and time(s).
4.1.2 Detail section
Information to be provided in the Detail section:
0220 UNS, Section control
A segment to avoid segment collision.
0230 Segment group 5: DTM-LOC-NAD
A group of segments identifying dates and locations of current
and previous inspections, and may include the date of the next
safety inspection due as required under the International
Convention for Safe Containers (CSC) or the U.S. Federal
Highway Administration (FHWA), if indicated on the equipment.
It may also indicate the date and location of manufacture, and
name of manufacturer.
0240 DTM, Date/time/period
A segment to specify the date and time of the current or
previous inspection, or of manufacture.
0250 LOC, Place/location identification
A segment to specify the location at which the event
described in the previous DTM occurred.
0260 NAD, Name and address
A segment to indicate the name and address of the inspection
company, manufacturer, etc. relating to the event described
in the previous DTM.
0270 Segment group 6: RFF-DTM-NAD-MOA
A group of segments indicating information relating to
authorization for repair to proceed and acceptance of
responsibility for respective charges for such repairs. The
approval number, date, and name and address of the approving
party, and the monetary amount authorized are included within
the group.
0280 RFF, Reference
A segment indicating the authorization number attributable
to all or part of the estimate, which is provided by the
party.
0290 DTM, Date/time/period
A segment indicating the date and time at which the
authorization is provided.
0300 NAD, Name and address
A segment indicating the name and address of the authorizing
party.
0310 MOA, Monetary amount
A segment indicating the amount of money authorized to be
expended to the account of the authorizing party.
0320 Segment group 7: LIN-DIM-QTY-FTX-SG8-SG9-SG10
A group of segments indicating the type and amount of damage
found on the equipment during an inspection, and a description
of, and allocation of responsibility for, amount, type, extent,
and estimated cost of repairs needed to rectify such damage.
0330 LIN, Line item
A segment indicating a number for each damage line-item in
the message. The line number corresponding to a damage and
repair will remain constant throughout all versions of the
message, so that subsequent versions of the repair estimate
may be compared to previous versions. Items to be deleted or
altered in subsequent versions may also be highlighted in
this segment.
0340 DIM, Dimensions
A segment used to indicate the dimensions of the repaired
area.
0350 QTY, Quantity
A segment used to indicate the number of repairs of the
identical type to be performed.
0360 FTX, Free text
A segment to specify free form or processable supplementary
information (such as an indication of conjunctive or
alternate repair) that apply to a single damage and repair
line item.
0370 Segment group 8: DAM-COD
A group of segments describing damages, involved components
(including material for such components), and action to be
taken due to presence of the damage (such as repair).
0380 DAM, Damage
A segment to specify equipment damages, such as location,
type, and size of damage; and repair or other action
taken.
0390 COD, Component details
A segment to specify components involved in the repair,
by type of material.
0400 Segment group 9: RTE-QTY
A group of segments indicating the labor rate per hour (or
other unit time), and the number of hours (or time units)
needed to perform the repair.
0410 RTE, Rate details
A segment indicating the labor rate per unit of time
(e.g. hour) at which the repair will be charged.
0420 QTY, Quantity
A segment indicating the number of time units (e.g.
hours) of labor to be charged for the repair.
0430 Segment group 10:NAD-SG11
A group of segments indicating parties responsible for the
repair described, and the allocation of charges, broken down
category, applicable to such repairs, including any tax or
discount.
0440 NAD, Name and address
A segment indicating the name and address of the party to
whose account the repair will be charged.
0450 Segment group 11:MOA-TAX-MEA
A group of segments indicating the monetary amount of
charges for, the repair, and any tax and or discounts and
surcharges associated with labor and or materials charges
for the repair.
0460 MOA, Monetary amount
A segment indicating the monetary amount of labour,
materials, or tax applicable to the repair for which
the indicated party is responsible.
0470 TAX, Duty/tax/fee details
A segment indicating the rate of tax applicable to the
associated labor or materials charges.
0480 MEA, Measurements
A segment indicating a multiplier associated with
charges for labor or materials. If a discount applies,
the multiplier will be less than one; if a surcharge
applies, the multiplier will be greater than one.
4.1.3 Summary section
Information to be provided in the Summary section:
0490 CNT, Control total
A segment to provide message control totals.
0500 UNT, Message trailer
A service segment ending a message, giving the total number of
segments in the message and the control reference number of the
message.
4.2 Data segment index (Alphabetical sequence by tag)
BGM Beginning of message
CNT Control total
COD Component details
COM Communication contact
CTA Contact information
CUX Currencies
DAM Damage
DIM Dimensions
DTM Date/time/period
EQD Equipment details
FTX Free text
GIS General indicator
IMD Item description
LIN Line item
LOC Place/location identification
MEA Measurements
MOA Monetary amount
NAD Name and address
QTY Quantity
RFF Reference
RTE Rate details
TAX Duty/tax/fee details
TDT Details of transport
UNH Message header
UNS Section control
UNT Message trailer
Contents of DESTIM